Dubens padėkliukas CleanProtectPet, permatomas, 30x30 cm

Trumpai apie prekę

Prekė: Dubens padėkliukas CleanProtectPet, permatomas, 30x30 cm. Kategorija: Dubuo.

• Gamintojas: Vitis
• Modelis: brak
• Skersmuo: 30 cm
• Talpa: 30 ml
• Medžiaga: other

The Clean Protect Pet protective cover is a great way to keep your pet's bowl or litter box clean. The film protects the floor from moisture and dirt that may cause damage in the form of bulges. Clean Protect Pet also protects floors from scratching the floor with claws.

Check out the other listings – the overlay is available in the following dimensions:

• 30x30 cm
• 50x50 cm
• 50x60 cm
• 40x60 cm
• 40x80 cm
• 60x80 cm
• 50x100 cm

Clean Protect Pet Self-Adhesive Protective Cover is:

• easy and quick installation - self-adhesive
• odorless
• practically invisible - does not cover the floor
• safe for humans and animals – does not allergize
• resistant to detergents
• does not hook with shoes - total thickness only 0,17 mm (170 microns)
• waterproof - protects against moisture
• protects against claw marks on the floor

Additionally:

• no traces after removal
• application temperature: min +8°C
• application temperature -40 - +80°C
• Anti-slip - anti-slip certificate R11 DIN51130
• anti-flammable - non-flammability certificate B1 DIN4102

Assembly instructions:

Dry gluing method

(requires more practice due to the inability to peel off and re-stick the film if correction is necessary)

Recommended tools:

• Clean Protect IZO universal degreaser,
• squeegee.

1a) Surface (floor, stairs, windows, doors, etc. ) should be cleaned dry and then degreased with a cloth soaked with degreasing agent, e.g. Clean Protect IZO available at our auctions.

It should be remembered to test the effect of the preparation on a small, invisible fragment of the glued surface.

2a) We gradually remove the protective paper and stick Clean Protect pads from the shorter side gradually peeling off the tape.

3a) The surface of the film is leveled with a cloth or squeegee (available at our auctions). If air bubbles form, they can be pierced with a needle.

4a) Ready!

Wet bonding method

(allows correction of the position of the film, recommended especially in the case of wrapping larger areas)

Recommended tools:

• Clean Protect IZO universal degreaser,
• liquid for application of Clean Protect WET film,
• squeegee,
• paper towels.

1b) Surface (floor, stairs, windows, doors, etc. ) should be cleaned dry and then degreased with a cloth soaked with degreasing agent, e.g. Clean Protect IZO available at our auctions.

• It should be remembered to test the effect of the preparation on a small, invisible fragment of the glued surface.

2b) We abundantly and evenly spray Clean Protect WET liquid on the place where the film will be applied.

• For wood surfaces, wood-like panels, etc. Remember to spray only places well protected against water penetration.

3b) We gradually remove the protective paper and put the film on a wet surface and put it in the right place.

4b) We smooth the foil with a squeegee squeezing water from underneath, starting from the center towards the edges. Pay attention not to move the film. Wipe the water with a paper towel or absorbent cloth.

It is worth remembering:

- in the case of varnished surfaces, it is recommended to use overlays not earlier than about a week after varnishing. This is the time necessary to completely dry the varnish.

- in the case of using overlays on varnished surfaces, it is worth performing a test of varnish hardness by sticking and peeling off a small fragment of the overlay.

-before peeling off used overlays, it is worth heating the overlays (e.g. with a dryer) – glue residues can be removed with a cloth soaked, e.g. Clean Protect label.

Safe delivery in cardboard tubes – the pad is well protected and is not exposed to damage and bending. In addition, the tubes are protected with stretch film to protect against rain/moisture during delivery of the package.

Specifications